Details
AM-CP4 Console Panel
Notify me when product is back in stock£100.00 inc. tax
Description This module is recreation of the Moog CP4 Console Panel with filter CV routing, and Trigger & Envelope Control for two sets of 911 and 902 modules. The CP4 was part of the 1967 range of Moog Modular modules, and seen in the IP and IIC. The nearly identical CP4A was part of the 1973 range, and seen in the Moog 35.
This handy module reduces external patching by providing CV and Trigger routing via switches. with LED indicators The AMSynths version contains dual V to S-Trigger converters, which are Eurorack compatible.
The left hand side of the panel provides filter CV routing with four indepedent inputs that can be switched on or off (red LED indication). The fourth input has an attentuator potentiometer and a green LED indicator. All inputs are mixed together at unity gain using a precision Op Amp and can be used to drive VCO's as well as filters.
The output CV can be manually patched into the CV input of a 904A or 904B filter module, to control frequency cutoff. The output is also available internally for patching to an AMSynths 904 or 904B filter module, which have internal inputs.
The right hand side of the panel provides trigger selection from two V-trigger inputs, which are converted to S-Triggers and internally patched to two 911 modules. At the top of the panel there are two toggle switches (red LED indication), to select the trigger signal inputs. The LED's indicates the presence of a gate signal when in the switch is in the on position.
The left hand column of switches (orange LED indication) route the selected S-trigger signals to two modified Behringer 911 modules (LEFT and RIGHT).
The right hand switches (with green LED's) connect the DC control voltages from the 911's to their respective 902 Voltage Controlled Amplifiers (LEFT and RIGHT).
The AM-CP4 module has a 12V Eurorack power inlet socket, ten slide switches and LED’s. The module connects to Behringer 902 and 911 modules via an included cable harness that uses Molex 2 pin connectors. There is a small daughter PCB that attaches to the back of each of the 902 and 911 module that is included with this module.
Molex connectors are used to provided the inter module cabling, with the customer needing to solder wires to the various Behringer jack sockets from the daughter PCB’s. This is an easy job for someone competent in soldering and instructions are included with the module. There is a picture of this within the product pictures above.
The Behringer jack sockets on the 911 and 902 are not normalised, so no PCB traces are cut.
Eurorack Module: 16HP wide
Installation Manual: Download PDF
The AM-CP4 module is designed to complement the Behringer System 55 Modular System, and enable customers to build an accurate Moog IP, IIC or 35 system. The module has a 16HP black anodised aluminum and comes with a set of M3 mounting screws and washers, and a standard Doepfer power cable.
PLEASE NOTE: SOME SOLDERING IS NEEDED TO INSTALL THIS MODULE.
PRODUCT STATUS: IN DEVELOPMENT
This handy module reduces external patching by providing CV and Trigger routing via switches. with LED indicators The AMSynths version contains dual V to S-Trigger converters, which are Eurorack compatible.
The left hand side of the panel provides filter CV routing with four indepedent inputs that can be switched on or off (red LED indication). The fourth input has an attentuator potentiometer and a green LED indicator. All inputs are mixed together at unity gain using a precision Op Amp and can be used to drive VCO's as well as filters.
The output CV can be manually patched into the CV input of a 904A or 904B filter module, to control frequency cutoff. The output is also available internally for patching to an AMSynths 904 or 904B filter module, which have internal inputs.
The right hand side of the panel provides trigger selection from two V-trigger inputs, which are converted to S-Triggers and internally patched to two 911 modules. At the top of the panel there are two toggle switches (red LED indication), to select the trigger signal inputs. The LED's indicates the presence of a gate signal when in the switch is in the on position.
The left hand column of switches (orange LED indication) route the selected S-trigger signals to two modified Behringer 911 modules (LEFT and RIGHT).
The right hand switches (with green LED's) connect the DC control voltages from the 911's to their respective 902 Voltage Controlled Amplifiers (LEFT and RIGHT).
The AM-CP4 module has a 12V Eurorack power inlet socket, ten slide switches and LED’s. The module connects to Behringer 902 and 911 modules via an included cable harness that uses Molex 2 pin connectors. There is a small daughter PCB that attaches to the back of each of the 902 and 911 module that is included with this module.
Molex connectors are used to provided the inter module cabling, with the customer needing to solder wires to the various Behringer jack sockets from the daughter PCB’s. This is an easy job for someone competent in soldering and instructions are included with the module. There is a picture of this within the product pictures above.
The Behringer jack sockets on the 911 and 902 are not normalised, so no PCB traces are cut.
Eurorack Module: 16HP wide
Installation Manual: Download PDF
The AM-CP4 module is designed to complement the Behringer System 55 Modular System, and enable customers to build an accurate Moog IP, IIC or 35 system. The module has a 16HP black anodised aluminum and comes with a set of M3 mounting screws and washers, and a standard Doepfer power cable.
PLEASE NOTE: SOME SOLDERING IS NEEDED TO INSTALL THIS MODULE.
PRODUCT STATUS: IN DEVELOPMENT
Product Code: AM-CP4
Product Condition: New
weight: 350.0g
0 Units in Stock
Updating Order Details
Please do not refresh or navigate away from the page!
Customer Reviews
No Reviews Posted Yet - be the first!
write review